Lighting

Flexible Versatite™ mount for Dash, Zot, Dart, Hotrod, Hotshot Micro 2W, Hotshot Pro 200 (flexible mount version; not for Hotshot Pro 200C) systems. Compatible with most handlebars, seat posts, and seat stays including aero styles.

Lezyne's Go-Pro LED Adapter allows you to mount your Lezyne LED light to any standard Go-Pro mount. This makes it fast and easy to switch swap out your camera and headlight using the same mount.

Recon-E Light to Bosch motor unit connector cable.

A universal quick release mount that attaches to round-shaped drop and flat handlebars.

Recon-E Light to Shimano motor unit connector cable.

- Rack mount bracket only - Fits TL-L225 taillight

- Attaches to rear racks - Compatible with: Blinky 3,5,7 and Superflash - 25mm between each of the top horizontal holes (center to center) - Requires an "L bracket" that typically comes with a rear rack. If your rack is missing the L bracket, you can purchase Planet Bike's rack hardware pack

- Replacement aero mount for Numen light

Mounting bracket for MSW front White Bat Headlight. - Includes 1 front mounting bracket

Replacement bracket for Pico and Tigermoth lights. - Includes 1 front bracket, 1 rear bracket, and 2 mounting straps

- Fits seatpost (up to 31.8mm) or seatstay - Compatible with: Blinky 3,5,7, all Superflash lights and Blinky Safety rear light - Use with Blinky Safety Front light bracket to fit oversize (~31.8mm) handlebars

SP-12 Flex-Tight Seatpost Bracket for most CatEye taillights

- Compatible with all Blaze headlights, Beamer 1/3/5, 1200, Dual Spot, and Bright Spot bike headlights - Fits 25.4 – 31.8mm handlebars

- Fits 25.4-31.8mm handlebars - Compatible with Blaze, Beamers, 1200, 5000x and Super Spot

Mount your tail light to the reflector tab on the back of a rear cargo rack with this Rack Bracket from Portland Design Works. - Compatible with all PDW rear lights except the Asteroid and Fenderbot - Horizontal holes are 50mm apart to fit European rack standards - Vertical holes are 18mm apart to fit most reflector mounts

- Simplistic safety light designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries - Lumens: 12

- Simplistic safety light designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries - Lumens: 6

Others out on the roads and paths will see you when Sunlite's TL-L340 Taillight is on your bike. It sports 3 bright LEDs, steady and flashing modes, and a long run time.

Giant's Numen TL1 5 LED Taillight boasts 5 bright LEDs so you get noticed out on the road. If that wasn't enough, you have 4 modes: steady, flashing, patrol, and random modes for high visibility in traffic. And it runs for up to 180 hours. This great water-resistant light also sports 2 mounting options.

The NiteRider Tail Light Strap Mount allows for quick installation and fitment on to standard seat posts. It features a quick release tab that allows you to remove just your tail light, leaving the strap mount installed on the seat post; ideal for when you leave your bike unattended or when it's time for a recharge. System Compatibility - Sentinel - Solas - Sabre - CherryBomb - TL 5.0 SL Not compatible with omega 300 and sentry aero 260 tail lights.

-Mounts easily to front racks with threaded M5 mounts -Allows for unobstructed light positioning -22.2mm clamping diameter

Put it on your seatpost, put it on your seatstay, put it anywhere—Sunlite's Griplite goes everywhere. This powerful little light boasts two LEDs and runs for a whopping 100 hours! It has steady and two flashing modes, and is housed in a water-resistant body.

Put it on your handlebars, put it on your fork leg, put it anywhere—Sunlite's Griplite goes everywhere! This powerful little light has 2 LEDs and runs for a whopping 100 hours! It has steady and flashing modes and is housed in a water-resistant body.

• 2 bright Nichia LEDs • Uses 2 CR 2032 lithium batteries (included) • 100 hour run time • 3 modes: 2 flashing and 1 steady • Water-resistant silicone body

• 2 bright Red LEDs • Includes 2 (CR 2032) lithium batteries • 100 hour run time • 3 mode (2 flashing modes & steady mode) • Water resistant silicone body

Lezyne's Composite Bar Mount is a hard mount made of a reinforced Composite Matrix cradle for a strong and secure attachment of the Mega Drive, Deca Drive, and XL LED lights to the handlebar. It is designed for 25.4 mm or 31.8 mm bars, with the cradle designed to pivot 15 degrees laterally to allow adjustment of the LED light beam angle and directing it where it is most needed. A large thumb screw secures the CM mount to the bar without need of tools, and can be tightened by hand or a 1mm hex key. Molded rubber shims add grip and fine-tune fitting to undersized bars. Composite Bar Mounts are sold in a kit with the Mega Drive, Deca Drive, or XL LED lights.

Sunlite's HL-K100 Headlight is a great light at a great price. It sports a super-bright Krypton bulb housed in a tough, water-resistant body so it's perfect for commuting year round. A no-tools-required quick-release handlebar mount is included, too.

Be seen with CatEye's Omni 3 Taillight, which uses Omni Directional Technology for 360 degrees of visibility. Three super-bright LEDs light up in three different modes so you can customize the pattern and get run times up to 200 hours. Plus, CatEye's tool-free mount makes installation a breeze.

Mount your Cygolite bicycle headlight to a variety of GoPro compatible interfaces and third-party mounting options that are compatible with the GoPro interface. - Compatible with Ranger, Expilion, Metro, and Streak series - Includes adapter piece only

Mount the Nip light to an e-Bike that has the specialty Pro Max stem for accessories.